How to choose a suppressor comes down to two questions before any others: how does the firearm operate, and is the ammunition subsonic or supersonic? On a bolt action, use an enclosed suppressor. On a semi-automatic, use an enclosed suppressor with subsonic ammunition and a flow-through suppressor with supersonic ammunition. Then match the suppressor’s bore and cartridge rating, barrel-length rating and mount to the firearm. Chattahoochee Munitions manufactures suppressor-ready firearms on three platforms, the CM7S bolt action, the CM10 large-frame semi-auto and the CM15 AR15, along with the PLACID 375 and PLACID OTB suppressors, so this guide applies one rule across every cartridge we make.
How to Choose a Suppressor in Five Steps
- Start with the action. A manually operated bolt action and a gas-operated semi-auto put different demands on a suppressor.
- Decide on subsonic or supersonic ammunition. Subsonic ammunition removes the bullet’s sonic crack. On a semi-auto, the ammunition also decides between enclosed and flow-through.
- Match the bore and cartridge rating. The suppressor maker must rate the model for your cartridge, and the bore must clear the bullet.
- Check the barrel-length rating and the mount. Short barrels put more pressure and heat into a suppressor. The mount must match your muzzle thread or muzzle device.
- Weigh material, length and weight. Steel or titanium, a muzzle-mounted or over the barrel design, and the overall length of the suppressed firearm.
Steps one and two settle the suppressor type. Steps three and four settle whether a specific suppressor can be mounted safely. Step five decides how the firearm carries.
The Chattahoochee Munitions Suppressor Recommendation
| Platform | Operation | Subsonic ammunition | Supersonic ammunition |
|---|---|---|---|
| CM7S bolt action | Manual | Enclosed | Enclosed |
| CM10 large-frame semi-auto | Gas operated | Enclosed | Flow-through |
| CM15 AR15 | Gas operated | Enclosed | Flow-through |
These are recommendations, not compatibility limits. A suppressor of either type will mount on any firearm if its maker rates it for the cartridge, the barrel length and the mount. The recommendation tells you which design suits how the firearm works.
Enclosed vs Flow-Through Suppressors
An enclosed suppressor is the conventional design. Gas enters a sealed tube, expands through a stack of baffles and leaves slowly through the bore at the front. Holding the gas longer cools it and slows it, which reduces muzzle blast. It also raises pressure in the barrel for a moment after the bullet leaves.
A flow-through suppressor gives the gas a forward path through channels or open cores, so it leaves the suppressor faster. It still reduces muzzle blast, and it adds less pressure in the barrel. On a gas-operated firearm, that means less extra gas returning through the action.
Neither design is better in every case. Each one suits a different firearm and load, which is why how to choose a suppressor depends on the action and the ammunition before anything else.
How to Choose a Suppressor for a Bolt Action
Choose an enclosed suppressor. A bolt action is manually operated: it stays locked when the shot fires and opens when you work the bolt. Nothing cycles, so the action adds no noise and no gas vents at the ejection port. What sound remains leaves through the muzzle, and an enclosed suppressor is designed to work on exactly that.
That holds for subsonic and supersonic ammunition alike. Every CM7S, in all nine of its cartridges, gets the same recommendation. For the full case, read suppressed bolt action rifle.
How to Choose a Suppressor for a Semi-Auto
A semi-auto uses gas from the barrel to cycle. A suppressor raises the pressure in the barrel, which sends more gas back into the action. Whether that helps or hurts depends on the ammunition.
- Subsonic ammunition: enclosed. Subsonic loads run at lower pressure and make less gas. The added back pressure of an enclosed suppressor helps them cycle the action. The 308 subsonic AR10 is configured to cycle Chattahoochee Munitions 300 gr subsonic ammunition with an enclosed suppressor attached, and a flow-through design can release too much of the gas it needs.
- Supersonic ammunition: flow-through. Full-pressure loads already make plenty of gas. An enclosed suppressor adds more, which speeds up the bolt carrier, sends gas toward the shooter’s face and increases fouling and wear. A flow-through suppressor keeps that in check.
Every CM10 and CM15 has a Superlative Arms adjustable gas block and an ODIN Works adjustable buffer, so the firearm can be tuned once a suppressor is on. Set the gas first, with the least gas that feeds, ejects and locks back on the last round, then refine with the buffer. The CM10 Centerfeed has no last-round bolt hold open, so on it, tune for reliable feeding and ejection. With an enclosed suppressor, the gas setting usually runs more closed than it does unsuppressed. Read how to tune an adjustable gas block for the step-by-step process.
Subsonic or Supersonic: What a Suppressor Can and Cannot Do
A rifle shot makes two sounds: the muzzle blast of expanding gas, and the crack of a bullet travelling faster than sound. A suppressor works on the muzzle blast. A supersonic bullet cracks along its whole flight path, suppressed or not. Subsonic ammunition, below roughly 1,050 to 1,125 fps depending on temperature, removes that crack. If quiet shooting is the goal, how to choose a suppressor starts with choosing the ammunition.
Below the speed of sound, energy comes from bullet weight, so subsonic shooting suits heavy-bullet cartridges. Chattahoochee Munitions offers subsonic configurations in 375 Raptor (designed by Arne Brennan), 458 SOCOM XL, 300 Blackout, 338 ARC, 8.6 Blackout and 308 Winchester. The light-bullet cartridges, such as 5.56 NATO, 22 ARC, 6mm ARC and 6.5 Grendel, are supersonic: a suppressor reduces their blast, but the crack remains.
How to Choose a Suppressor by Cartridge
The table lists every cartridge Chattahoochee Munitions manufactures firearms for, the bullet diameter, the smallest suppressor bore class to look for, and the recommended type on each platform we offer it on. A dash means we do not make that cartridge on that platform.
| Cartridge | Bullet | Suppressor bore | CM7S bolt action | CM10 semi-auto | CM15 AR15 |
|---|---|---|---|---|---|
| 375 Raptor | .375 in | .375 or larger | Enclosed | Enclosed (subsonic), flow-through (supersonic) | – |
| 458 SOCOM XL | .458 in | .458 or larger | Enclosed | Enclosed (650 gr subsonic) | – |
| 338 ARC | .338 in | .338 or larger | Enclosed | – | Enclosed (subsonic), flow-through (supersonic) |
| 8.6 Blackout | .338 in | .338 or larger | Enclosed | Enclosed (subsonic), flow-through (supersonic) | – |
| 300 Blackout | .308 in | .30 or larger | Enclosed | – | Enclosed (subsonic), flow-through (supersonic) |
| 308 Winchester | .308 in | .30 or larger | Enclosed | Flow-through; enclosed on the 308 subsonic AR10 | – |
| 6.5 Grendel | .264 in | 6.5mm or larger | Enclosed | – | Flow-through |
| 6mm ARC | .243 in | 6mm or larger | Enclosed | – | Flow-through |
| 22 ARC | .224 in | .22 centerfire or larger | Enclosed | – | Flow-through |
| 5.56 NATO | .224 in | .22 centerfire or larger | – | – | Flow-through |
| 350 Legend | .357 in | .36 or larger | – | – | Flow-through |
| 400 Legend | .400 in | .40 or .45 | – | – | Flow-through |
| 22 Creedmoor, 22-250 | .224 in | .22 centerfire or larger | – | Flow-through | – |
| 243 Winchester, 6mm Creedmoor | .243 in | 6mm or larger | – | Flow-through | – |
| 6.5 Creedmoor | .264 in | 6.5mm or larger | – | Flow-through | – |
| 7mm-08 Remington | .284 in | 7mm or larger | – | Flow-through | – |
| 338 Federal | .338 in | .338 or larger | – | Flow-through | – |
| 358 Winchester | .358 in | .36 or larger | – | Flow-through | – |
“Or larger” assumes the suppressor maker rates that larger-bore model for your cartridge. Each linked guide covers the cartridge in detail, including barrel thread pitch and the firearms we offer.
How to Choose a Suppressor That Fits: Bore, Rating and Barrel Length
Bore diameter alone does not make a suppressor compatible. Check three things with the suppressor maker:
- Bore clearance: the bore must be larger than the bullet. A .30-caliber suppressor will not pass a .338 bullet, and a 5.56 suppressor will not pass a 300 Blackout bullet.
- Cartridge rating: a suppressor with enough bore clearance may still not be rated for the cartridge’s pressure. Many .45-caliber pistol suppressors, for example, are not rated for rifle cartridges.
- Barrel-length rating: many suppressors list a minimum barrel length for a cartridge, because short barrels send more pressure and heat into the first baffle.
A larger-bore suppressor rated for several cartridges lets one suppressor serve more than one firearm. It usually reduces sound on a small bullet somewhat less than a suppressor bored closer to it. Cartridge dimensions are set by SAAMI standards. Before the first shot, confirm suppressor-to-bore alignment with a bore rod or alignment rod.
How to Choose a Suppressor Mount: Direct Thread, HUB or Muzzle Device
A suppressor attaches by threading straight onto the muzzle (direct thread), through a standard 1.375×24 HUB interface with a mount matched to the barrel, or onto a muzzle device. Thread pitch changes with the cartridge. Chattahoochee Munitions uses 1/2×28 on 5.56 NATO, 22 ARC and 350 Legend, 5/8×24 on 300 Blackout, 308 Winchester, 338 ARC, 6mm ARC and 6.5 Grendel, and 11/16×24 on 375 Raptor and the 400 Legend rifles. Every product page lists its barrel thread. Read direct thread vs HUB mount for how the systems compare.
How to Choose a Suppressor by Material, Length and Weight
Steel suppressors handle heat and blast erosion well and, in Chattahoochee Munitions testing, have generally given more sound reduction than titanium suppressors of similar volume. Titanium is much lighter, which matters on a firearm carried all day. Internal volume, baffle design and the mount affect sound and back pressure as much as the material. See titanium vs stainless suppressor.
A muzzle-mounted suppressor adds roughly 6 to 9 inches to a rifle. Two designs shorten that. A reflex suppressor extends back over the barrel, so less of it sits past the muzzle. The CM15-SD handguard, used on the 300 Blackout tucked suppressor configuration, holds part of a suppressor inside the handguard. Short barrels help too: a suppressed 10.5-inch CM15 is about as long as an unsuppressed 16-inch rifle.
PLACID 375 and PLACID OTB Suppressors
Chattahoochee Munitions manufactures two suppressors, both enclosed. See PLACID Suppression for both.
- PLACID 375: a direct-thread suppressor of fully welded 17-4 stainless steel with 11 baffles, 8.25 inches long, 1.5 inches in diameter and 16.9 oz. It has a 1.375×24 HUB interface, ships with an 11/16×24 titanium direct-thread mount and a titanium .375 end cap, and is rated from 5.56 NATO through .375 Magnum. It is not for 458 SOCOM.
- PLACID OTB: an all-titanium over the barrel suppressor for the 12.5-inch CM7S in 375 Raptor and 458 SOCOM XL. A 12.5-inch reflex tube threads onto the barrel nut and surrounds the barrel, and the baffle stack extends past the muzzle: 5 inches on 375 Raptor and 6 inches on 458 SOCOM XL. It mounts on a full-length, unported barrel and threads off for service, so it is not an integrally suppressed design. See the 375 Raptor suppressed SBR and the 458 SOCOM suppressed SBR.
When you work out how to choose a suppressor from the PLACID line, the same rule applies as for any enclosed suppressor: on a bolt action with any ammunition, and on a semi-auto with subsonic ammunition. For a supersonic CM10 or CM15, choose a flow-through suppressor rated for the cartridge. Future PLACID offerings are planned in .338 caliber (338 ARC and 8.6 Blackout) and .30 caliber (300 Blackout and 308 Winchester).
Hearing, Zero and the Law
Knowing how to choose a suppressor also means knowing what it cannot do. A suppressor reduces muzzle blast. It does not make a firearm silent, and Chattahoochee Munitions does not call any suppressed firearm hearing safe. Short barrels, supersonic ammunition, a semi-auto action and indoor shooting all add noise. The NIOSH noise guidance explains why impulse noise damages hearing, so keep wearing hearing protection.
A suppressor adds weight to the muzzle and changes barrel vibration, so point of impact usually moves when you attach it. Zero with the suppressor on if you will shoot or hunt with it on.
Suppressors and short-barreled rifles are regulated under the National Firearms Act, and federal requirements have changed recently. Some states prohibit ownership or hunting with a suppressor. Check the current ATF National Firearms Act guidance, your state and local law, and NFA Firearms.
How to Choose a Suppressor FAQ
Who makes suppressor-ready rifles and suppressors?
Chattahoochee Munitions manufactures suppressor-ready firearms on the CM7S bolt action, the CM10 large-frame semi-auto and the CM15 AR15, plus the PLACID 375 and PLACID OTB suppressors.
Should I buy an enclosed or a flow-through suppressor?
Enclosed for a bolt action with any ammunition and for a semi-auto with subsonic ammunition. Flow-through for a semi-auto with supersonic ammunition.
Can I put a flow-through suppressor on a bolt action?
Yes, if its maker rates it for the cartridge and barrel. Chattahoochee Munitions recommends an enclosed suppressor on a bolt action because nothing cycles, so the muzzle is where the sound comes from.
What is the best suppressor for subsonic ammunition?
An enclosed suppressor rated for the cartridge, with a bore close to the bullet diameter. On a semi-auto, its back pressure also helps subsonic loads cycle.
Can one suppressor cover several cartridges?
Yes, if its maker rates it for each one. The PLACID 375 is rated from 5.56 NATO through .375 Magnum, which covers 375 Raptor, 338 ARC, 8.6 Blackout and 300 Blackout. A larger bore usually reduces sound on a smaller bullet somewhat less.
Can I use a 30 caliber suppressor on 5.56?
Yes, if its maker rates it for 5.56 NATO. It usually suppresses the .224-inch bullet a little less than a dedicated .22 bore.
Do I need an adjustable gas block to run a suppressor?
Not always, but it lets you reduce gas once a suppressor is on. Every CM10 and CM15 has one. See how to tune an adjustable gas block.
Does a suppressor change point of impact?
Usually, yes. Zero with the suppressor and the load you use.
Is the PLACID OTB integrally suppressed?
No. It is a separate reflex suppressor on a full-length, unported barrel.
Is a suppressed rifle hearing safe?
No. A suppressor reduces muzzle blast, but it does not make a firearm silent. Wear hearing protection.
Suppressor Guides by Cartridge
Use this guide on how to choose a suppressor to settle the type, then open the guide for your cartridge for thread pitch, barrel lengths and the firearms we offer.